Panda Helper Panda Helper iOS
VIP Versiyon serbest Sürüm Jailbreakli Sürüm
- Panda Helper >
- Android Apps >
- Amper
Uygulama Ekran Görüntüsü
Değiştirilmiş Açıklama
kilitsiz
Açıklama
Bataryanızın şarj ve deşarj akımını ölçün.
PRO özellikleri:
- Widget'lar
- Bildirim
- Cihazdaki uyarılar
- Alerts on Android Wear
Not every device is supported because there are devices which lacks an appropriate measurement chip (or the interface) and they can not be supported at all. Please read the list of not supported phones at the end of the description.
Uygulamanın mA doğruluğuna sahip olması amaçlanmamıştır. It is only good for evaluate which Charger/USB cable combo is working the best for you on the same device.
----
Please read also the FAQ: http://goo.gl/R8XgXX
----
Start the app and wait ca. 10 seconds ("measuring" is on the display). After this time, the charging or discharging current will be shown.
Akım birçok şeye bağlıdır:
- Şarj Cihazı (USB / AC / Kablosuz)
- USB kablosu
- Telefon türü
- Mevcut görevler çalışıyor
- Ekran parlaklığı
- WiFi durumu
- GPS durumu
Please don't use the readings on this app as concrete science. However, the readings are good enough to relatively measure how various chargers and USB cables fair on the same device.
If the app shows 0mA all the time, please use the settings option "Old measurement method". You can force the app with it to use the old measurement interface, if the Lollipop device has at least one.
Unfortunately some Samsung devices don't give correct (measured) values (e.g.: S5), just the maximum possible charging current with the actual USB cable/charger configuration. This is a firmware problem.
----
Arka plan bilgisi: The app measures the charging/discharging current of the battery. If your phone is not connected to a charger, you see the discharging current which is negative. If you connect a charger then the current what the charger gives will be used to supply your phone and the remaining power will be charged into the battery.
Telefonunuz bağlı bir şarj cihazı olmadan 300 mA tüketirse (ekranda -300mA), 500 mA'lik bir şarj cihazı pilinizi maksimum 200 mA akımla (ekranda 200mA) şarj eder.
----
Teknik bilgi: The displayed current is an average value from 50 measurements minus the 10 upper values and the 10 lower values. The displayed current can be shaky or unstable or even zero which means, that the Android system provides unstable values. Every company uses different battery types and other hardware making it difficult to get accurate results about your charger.
----
LiPo piller, telefonu şarj etmek için gereken tam süre boyunca maksimum güç tüketmez. Piliniz neredeyse tamamen doluysa, düşük pil seviyelerinde olduğu gibi şarj akımı çok daha az olacaktır.
- LiPo şarj aşamalarını açıklayan bir grafik: http://batteryuniversity.com/_img/content/ion1.jpg
- Dave'in (EEVBlog) LiPo Şarj Etme Eğitimi: http://youtu.be/A6mKd5_-abk
----
Phones/ROMS compatible only with "Old measurement method" switched on and selected the right "Measurement interface":
➤ HTC One M7 / M8
➤ LG G3
Phones/ROMS reported to be not working with this app:
➤ Galaxy Grand Prime - fortuna3gdtv
➤ Galaxy Note2 - t03g, t03gchn, t03gchnduos, t03gcmcc, t03gctc, t03gcuduos
➤ Galaxy S3 - d2att, d2spr, d2vmu
➤ Galaxy Tab4 7.0 - degas3g
➤ HTC Desire 510 - htc_a11ul8x26
➤ HTC One S (ville), X (endeavoru), XL (evita)
➤ HTC Sensation 4G - pyramid
Please do not give wrong rating, if your phone is one of the above. Not the app is wrong, but your phone does not support this kind of measurement yet.
If the app doesn't work on your device with pre-Lollipop Android version, then please read the first and the second posts in this XDA developer forum thread: http://goo.gl/pZqJg8 . Please post your problem with screenshots in the XDA thread.
Please read also the FAQ: http://goo.gl/R8XgXX
Bilgi
Name Amper
Kategoriler APPS
Geliştirici Braintrapp
Sürümü v3.41
Güncelleme 2024/04/16
Diller İngilizce
beden 9.43 MB
uygunluk Android 4.1 +
Root gerekli Gerek yok
Angry Birds Journey Hack Bilgileri
PUAN
Oy vermek için dokunun
